How to Install 15mm Calacatta Classique Tiles

## How to Install 15mm Calacatta Classique Tiles.

Installing 15mm Calacatta Classique tiles can transform your space with their elegant, marble-like appearance. Follow this step-by-step guide to ensure a professional and long-lasting finish.

### Gather Necessary Tools and Materials.

Before starting the installation, ensure you have the following tools and materials:

- Measuring tape.

- Tile saw or tile cutter.

- Notched trowel.

- Level.

- Tile spacers.

- Chalk line.

- Thin-set mortar.

- Grout.

- Rubber grout float.

- Sponge.

- Bucket of water.

- Safety gear (gloves, goggles).

### Prepare the Surface.

1. **Clean the Surface:**.

Start by cleaning the floor or wall where you will be installing the tiles. Remove any dust, dirt, or grease.

2. **Check for Level:**.

Use a level to ensure the surface is flat. If there are any uneven areas, apply a leveling compound and allow it to dry according to the manufacturer's instructions.

### Plan the Layout.

1. **Measure and Mark:**.

Measure the dimensions of the area to be tiled. Use a chalk line to snap a grid that helps align the first row of tiles.

2. **Dry Layout:**.

Lay out the tiles on the surface without adhesive to visualize the final appearance and make any necessary adjustments. This step is especially important for patterned tiles like Calacatta Classique.

### Mix and Apply Thin-Set Mortar.

1. **Prepare Mortar:**.

Mix the thin-set mortar according to the manufacturer’s instructions. It should have a peanut-butter-like consistency.

2. **Spread Mortar:**.

Using a notched trowel, spread the mortar evenly over a small section of the surface. Hold the trowel at a 45-degree angle to create ridges in the mortar.

### Install the Tiles.

1. **Set the Tiles:**.

Place the first tile at the intersection of the chalk lines, pressing it firmly into the mortar. Twist slightly to ensure a good bond.

2. **Insert Spacers:**.

Insert tile spacers between the tiles to ensure uniform gaps for grout lines.

3. **Continue Setting Tiles:**.

Continue placing tiles and spacers, working in small sections until the area is covered. Periodically check for level and adjust as needed.

4. **Cut Tiles to Fit:**.

Use a tile saw or cutter to trim tiles for edges and corners. Ensure that the cuts are precise for a seamless look.

### Allow Mortar to Cure.

Let the thin-set mortar cure for at least 24 hours before proceeding to grouting.

### Apply Grout.

1. **Mix Grout:**.

Prepare the grout according to the manufacturer’s directions.

2. **Apply Grout:**.

Using a rubber grout float, spread the grout diagonally across the tiles, pressing it into the gaps.

3. **Remove Excess Grout:**.

Hold the float at a 45-degree angle and scrape off any excess grout from the tile surface. .

4. **Clean Tiles:**.

After about 15-30 minutes, use a damp sponge to clean the tiles and remove any grout haze. Rinse the sponge frequently.

### Final Steps.

1. **Let Grout Cure:**.

Allow the grout to cure for at least 24 hours.

2. **Seal Grout:**.

Apply a grout sealer to protect against moisture and staining, especially important for high-traffic areas.

3. **Clean Up:**.

Clean any remaining residue and admire your newly tiled surface.

By meticulously following each step, you’ll achieve a flawless and professional finish with your 15mm Calacatta Classique tiles. Enjoy the luxurious new look of your space!

Contact us to discuss your requirements of 30mm Calacatta Laza Oro, Fine Shimmer Quartz Chinese. Our experienced sales team can help you identify the options that best suit your needs.