Oct. 28, 2024
Press brakes are an essential machine for bending metal. They&#;re used to create more complicated bends that other rollers aren&#;t generally equipped to handle. Many factors go into the operation of press brakes and choosing the right one can be difficult. To help you make the right choice, here are five essential attributes to keep in mind.
You will get efficient and thoughtful service from HAVEN.
You&#;ll need to keep how much power your press brake is going to use in the back of your mind as you&#;re shopping around. Your building may not support the amount of drain required by the press brake. This can be a problem, especially if a high-energy model is precisely what you need.
To rule out constraints or safety concerns, check your electrical system for compatibility first. Ensure that your electrical system supports your press brake's power demands, or find a way to increase your power supply.
Press brakes demand a significant amount of space, and they don't usually fit into smaller rooms. You may be tempted to opt for a smaller press brake to cut down on space consumption, but smaller isn&#;t always better&#;in fact, it can even be dangerous.
For special projects, larger machines are a must. They'll make your life easier, too, because they're more durable and rugged over time.
Certain types of tooling may only be used if your machine is tall enough and strong enough for the job. Moreover, not all toolings and accessories share compatibility with every model. Rule out contraindications before you shop, so you aren't left purchasing new tools.
Ensuring that your new press brake has the necessary software and hardware to handle the toolings you use is also a must. This issue isn't typical, at least with newer machines, but it's important enough that all buyers should rule it out. Create a list of the types of toolings and unique parts you use on a regular basis; then, ask your seller to clarify specifications to see if they match.
You should always oversize the press brake capacity by around 20 &#; 30% with respect to your data in order to allow for the variability in the characteristics of the metal and so that you are not in danger of working to the limits of the machine&#;s capacity.
One of the most common misjudgements is to confuse the total force needed to bend a given sheet metal part with the tons per metre for the specific thickness, material and die. Find out more in this guide.
Clearance is simply the front opening of the press brake. A press brake with a larger stroke is a machine equipped with greater intermediates that allow easier extraction of the bent parts.
Different metals have varying properties and behave differently when subjected to bending. For instance, aluminum is generally more malleable than stainless steel. Understanding the characteristics of the specific material you&#;re working with is essential in determining the appropriate press brake and bending parameters.
Our Ultimate Guide to Sheet Metal Materials provides expert insights and practical advice. Explore now to choose the perfect material for your project.
Complex press brakes offer advanced features and automation, but they often require skilled operators. If your team lacks the necessary expertise, consider the time and resources needed for training. Weigh the benefits of increased capabilities against the potential challenges of operator training and maintenance.
There are many different types of press brake machines. Each of these comes with its own set of advantages and limitations. You can choose the right press brake based on your use case. These different types of press brakes are:
Mechanical Press Brakes: simpler and more affordable, but with lower precision and speed.
Hydraulic Press Brakes: offer better precision and control but require more maintenance.
Pneumatic Press Brakes: fast and easy to operate but have lower force capacity than hydraulic presses.
Servo Press Brakes: highly precise and efficient.
CNC Press Brakes: fully automated for maximum productivity and accuracy.
Hybrid Press Brakes: combine the best features of hydraulic and electric press brakes for optimal performance.
Tandem press brake: particular configuration that involves the connection of two machines into one, but there are also solutions that combine three bending machines (tridem) or 4 bending machines (quadrem). Read our guide on "What to know before choosing a tandem press brake".
Secondary Factors to Consider For the Right Press Brake
Intermediates are adaptors to insert between the beam and the punches and are very useful because they allow deep box structures to be easily made.
The tool clumping systems are sub-divided into:
manual locks;
semi-automatic locks:
pneumatic blocks;
hydraulic locks;
The choice of correct locking is fundamental to reduce the work times and correctly manage the work zone.
It is a manual semi-automatic lock with rapid front locking-unlocking system of the punch. Operation is very simple and, compared to the traditional manual solution, allows faster and easier re-equipment of the machine.
In fact, by moving the locking lever, the punch is released to remove it from the front; while, on closure, the punch is automatically brought to stop and perfectly aligned.
The automatic tool locking systems allow equipping of the press brake in complete safety. The tools are automatically aligned, positioned and fastened. This solution drastically reduces the equipping time and considerably increases production.
Today, a modern and innovative solution exist that allows automated change of the punches and matrixes. For example, VICLA hybrid press brakes can be connected to an automatic tools warehouse that allows equipping, even on multiple stations, of higher and lower tools.
This system is customisable and designed to measure according to client requirements; it reduces setup by 4 or 5 times compared to manual tasks and automatically performs even the most complex equipping, managing 70 mm wide V matrices, rod holding tools and allowing the tool to rotate 180°.
Automation covers everything, including upstream operations. One of the more interesting aspects is programming by the technical office: the CAD/CAM system processes the three-dimensional file, creates the best bending cycle and sends the program to the machine that is automatically equipped, referencing the bending sequence directly on the numerical control. All tooling and machining data are automatically saved at the end of the work and exported to management for a 4.0 key data analysis.
The rear gauge is a motorised structure on which the references are set and can be moved and positioned to allow a variety of complex bends.
Movement of the back gauge along the depth of the machine is called axis X. Vertical lifting is called axis R.
It consists of very important and useful tools to support thin sheets. They are equipped with pneumatic operation and a Teflon coating that prevents marks on the material. They can also be activated by numerical control. There are 2 references and they are usually manual, but they can be automated and controlled directly by the CNC; the positioning of the stops is along the Z axis.
All towers are equipped on VICLA press brakes with a visual LED stop. Switch on of the LED ensures contact of the sheet with the reference.
In more accessorised versions, the towers are:
Motorised (axes z1- z2)
For more Hydraulic Forming Brakeinformation, please contact us. We will provide professional answers.
Independent (axes x2 - x3)
Anthropomorphic (axes r1 - r2)
The greater the length of a bending machine, the more the problems relating to the structural failure of the bench, making it more difficult to get a well worked part. Over the years, technological evolution has taken giant steps, passing from manual systems (such as using paper shims under the matrix) to automatic, mechanical or hydraulic systems, where a pre-load of the assumed deformation was determined. The limit of these systems is based on a theoretical calculation set by numerical control.
VICLA has developed an intelligent system that improves the work in the workshop: the active Clever Crowning system.
Thanks to special sensors in the beams, crowning enables measurement and compensates deformations in real time. There is no need to set any data; the system actively reacts to changes in characteristics.
Each press brake, despite its robustness, is subject to structural bending, during the bending phase, and obviously the deformations are much bigger the greater the effort the machine has to make.
The main deformation is crowning, which corresponds to bending of the beam which is pushed into position by the side cylinders; the other (and for many reasons semi-unknown), is called in jargon &#;yawn&#; and is the tendency of the frames to open in the throat zone.
Thanks to the Flex system the sheet metal press brake dynamically compensates any deformations based on the effort required: the CNC receives the data from the pressure sensors of the cylinders, which are interpolated in real time to establish the correction to implement.
It is not enough to just add an inverter to call a press brake "hybrid"; in fact, technological innovation revolves around a specific hydraulic system, which in the case of the standard hybrid model, includes a completely independent dual hydraulic circuit, each equipped with its own tank, motor, pump and inverter.
The functional separation of the two cylinders allows optimised control according to the load required for each cylinder; moreover, it allows efficiency to be achieved in terms of energy.
It is a system able to minimise wear of the machine by concentrating all its efficiency and automatically balancing the working pressure exclusively on the side that is used during bending of that specific part.
A further level of performance is provided by the Hybrid Plus model: the system consists of a brushless motor for each cylinder, capable of providing high forces and high movement speeds. It is an even more compact system consisting of a direct drive motor and pump, installed directly on the cylinders. with significantly reduced piping.
The results in numbers of this technological innovation are significant, as seen on the graph.
VICLA's angle control consists of two laser sensors mounted on linear guides that slide to the rear and front of the press brake bench taking the measurement in one or three points depending on the length of the piece.
Located on the sides of the matrixes, they have the purpose of reading, through a system of lasers and cameras, the inclination of the edges of the bends during deformation.
It is the most complete and performing solution for automatic angle measurement and control.
Angle reading takes place in 3 phases:
A laser beam is projected on the sheet metal surface
The camera detects the elastic recovery of the material
The CNC automatically sets the correction suitable to obtain the system desired angle that we use on our VICLA press brakes and is the best you can find on the market. The guaranteed precision is very high and in the order of fractions of a degree.
The system is also able to historicize the elastic recovery of the sheets, ensuring a constant and specific self-learning of the press based on the real situation of the company.
Obviously the angle control system guarantees the best performance if it is supported by solid and precise mechanics and perfect integration with numerical control.
With the latter, there is a continuous data exchange dialogue that allows perfect application with each item being processed.
If, for example, for volume issues, a specific bend cannot be measured by the angle control system, it can be "linked" to the previous reading made on another flap of the same piece.
Vicla optical angle control is a safe investment and surprisingly quick return as it makes continuous measurement operations by the operator completely unnecessary with an exponential increase in productivity and quality.
Probe angle control
There are essentially three types: inserts in the punch, hosted in the matrixes or applied to parallel sliding trolleys the exact same as those of the optical systems and placed on the sides of the bench.
On first examination, it could appear a definitive solution, however these are also not without limitations which, in practice, only appear during their real use.
The first is without doubt the installation difficulty. This is the typical limit of the controls inserted in the tools that include use of special punches and matrixes equipped with sophisticated, sensor-based strips.
Such angle control systems have very poor versatility when you consider they are not usable by changing tool set-ups.
Another limitation is their characteristic fragility.
Being small and very sophisticated mechanical elements, they are easily subject to failure caused by accidental impacts or malfunctions due to the accumulation of dust and dirt.
O.A.C. (Optical Angle Control)
Optical control is directly assembled on photocells to capture images of the profile detecting, calculating and correcting the bending angle.
One of the most sophisticated optical controls is the IRIS PLUS system. Although it is part of the optical angle control unit, IRIS plus is an alternative solution because it can perform an extremely accurate reading during the bending phase while remaining at a safe distance from the work area.
This eliminates any interference between the parts and the angle control devices and achieves totally versatile use.
The system, in fact, allows very interesting accuracy and reliability if the emitter and the receiver are not beyond a certain distance.
After approximately 2.5 metres, in fact, there is a natural increase in the phenomenon of refraction of light rays that reach the control system which are not sufficiently clear. The "noise" can be reduced by decreasing the sensitivity of the system but with the consequence of not ensuring the same accuracy in the reading of the bend.
The bottom bed has a bending/flattening table in order to perform flat hem bends without the need for a dedicated die. Its versatility makes it the ideal solution for companies that carry out many flat hem bends. The option is built directly into the die holder, and therefore can be used in conjunction with any other die that has a standard connection without the need to disassemble the table.
Front sheet metal supports
These front supports have a linear guide that extends beyond the bottom beam. Their height can be adjusted and they also slide sideways and rotate. A practical clamp-release system makes them very easy to mount and remove quickly.
They can lift weights up to 380kg. Use of the metal sheet bending followers offers an important advantage to reduce risks for the operator and increase the quality of the bent parts: it was designed to avoid counter-bend effects and reduce the need for other operators. It can also be easily removed from the front and placed on another bending machine.
An extension of the linear guides, extending beyond the bench. This solution is used to park the sheet metal supports when not in use.
It is powered by an integrated solar panel that allows you to get up to 20% more autonomy from battery life; it does not require connection, nor cable laying. The ultrasonic sensors are located on either side of the lower bench to transmit and receive data wirelessly.
The system indicates via the incorporated LED the right locking position of the equipment during tool configuration and indicates the position of the active tool in production mode.
It is a real and proper visual aid immediately available to the operator who, by doing so, does not waste time measuring and understanding where to position the tool and can dedicate his time to other operations.
Want more information on Press Brake Hydraulic System? Feel free to contact us.
Previous: None
Next: NC Shearing Machine vs. Traditional Options: Which Is Better?
If you are interested in sending in a Guest Blogger Submission,welcome to write for us!
All Comments ( 0 )