Dec. 02, 2024
Time needed: 14 hours
You will get efficient and thoughtful service from G.SB.
Here are the steps I used to stencil the large back wall in my home office:
Next I had to decide on colors. I already knew that I wanted to do white + the aqua color that I had already painted my office nook, but I had to choose which one would be the base color and which color I would stencil over top.
As I looked at different examples of stenciled walls, I realized that with the stencil pattern I had chosen, if I did the white as my base and the aqua color on top, I would have a more bold wall. And if I did an aqua base with a white stencil over it, my design would be a little more muted. Since I tend to be a bit scared of bold pattern, I decided to go with the latter combination.
The exact colors I used were Behr Marquee Cameo White and Sherwin Williams Rainwashed. (But I had Rainwashed color matched in the Behr Marquee paint since it is my favorite!)
To make sure that my stencil pattern would be completely straight, Donnie helped me draw a perfectly straight vertical line down the middle of the wall with a pencil.
That way I could set my first row of stenciling right against that line. Then all of the rest of my rows would be built upon that one, ensuring that they would all be straight.
To place the stencil the very first time, I lined it up with the pencil line that Donnie had drawn. I also placed it right up against the ceiling.
My stencil set came with a coordinating ceiling stencil. So if I started my design at ceiling level, I would be able to go back in with the smaller stencil later and easily fill in the little gap at the top. (You'll see what I mean in a minute!)
I just used painter's tape to adhere my stencil to the wall. Some of the instructions and tutorials I read recommended using a spray adhesive on the back of the stencil as well. But that sounded messy to me, so I used tape by itself. I didn't have any trouble.
I think one of the biggest keys to getting a nice, clean stencil line is to use very, very little paint. I opted to use a mini foam roller to apply most of the paint.
So I would load my roller and roll off some of the paint in my paint tray. Then I'd do a roll or two on a paper towel. This would ensure I had only a very thin layer of paint on my roller.
I would then roll a coat of paint over my stencil. Often, since there was so little paint on my roller, I would have to refill my roller 2-3 times and go over the stencil again to make sure it was completely filled in.
I found that doing several of these thin coats one right over the other worked well. It really minimized bleeding under the stencil.
At the top, bottom, and side edges of the stencil, there are registration marks that help make sure that the stencil is lined up in the correct position. I would typically finish rolling my paint and remove the stencil right away.
Then I'd let the paint dry for a minute or two and use the registration marks to position the stencil again.
Since I was using very thin coats of paint, they dried quickly. I didn't have to wait long in between stencils.
I also staggered the placement of the stencil, which allowed me to go more quickly. So, for example, while the paint for the stencil in the below photo was drying, I would remove the stencil and place it beside the top row. I'd roll the paint over that one, and then by the time I was finished there, I could move the stencil back down to the bottom. By then, the first stencil I had done was dry and ready to go.
The main part of the wall was a little time consuming, but the process was pretty straightforward' tape the stencil, paint, move the stencil, paint again, repeat. Eventually, though, that easier section was done, and it was time to tackle the edges.
As I mentioned previously, my stencil came with a smaller piece that was designed to help fill in the gap along the ceiling line. I actually ended up trimming down the top of the ceiling stencil by about 1/4' or so. This allowed me to place it right up against the ceiling rather than it rolling up onto the ceiling, which would make it harder to stencil.
For the smaller pieces like the ceiling and the edges, I used a stencil brush like the one below rather than a roller because it was easier to manipulate in the smaller spaces.
If there was a spot that was really teeny tiny, I kept a small paintbrush handy and used that to fill in when necessary.
My stencil didn't end up hitting the edges of my wall exactly. I had to do a bit of maneuvering to stencil each end and the very bottom of my wall.
I would first tape the edge of the opposite wall where I didn't want the paint to seep. Then I would just let the stencil bend into the corner and press it in with my fingers on one hand and stencil with the other hand.
The one piece of the wall that perplexed me a bit was a little two-inch strip between the door molding and the wall. There was no way to bend the stencil to make it fit neatly in that space. So I ended up cutting a two-inch strip out of my stencil once the rest of the wall was complete and using that to fill in the gap.
(If you were planning on using your stencil somewhere else and didn't want to cut it, one of my Instagram friends suggested making a photocopy of the stencil and cutting that, perhaps out of cardstock, which I thought was a great idea!)
As you can see, I taped up both the door frame and the wall so I wouldn't get paint on them, then taped my little piece of stencil into the gap, and just filled in with paint like I had on the other edges.
I pulled the tape away, and my wall was done! Yippee!
I did go in and end up touching up a few spots with paint where the lines weren't totally crisp. It still is not 100% perfect, but the pattern is pretty forgiving, so I didn't have to be too nit-picky with it.
I would say all in all I spent about 14 total hours stenciling. (And I tend to be kind of slow because I'm a perfectionist, so other people would probably be faster than me!)
My love for a wallpapered accent wall is no secret around here. But when I calculated up the cost for a large feature wall in our family room, I decided to find a more budget-friendly option. And my solution? A wall stencil! Today, I want to show you how to stencil a wall with paint. With a bit of work and lots of patience, you can indeed get the same same effect as wallpaper, but for a lot less!
A huge 'thank you' to Cutting Edge Stencils for providing the stenciling supplies for this project. I only work with brands and products I fully support and that make sense for my home, my family, and this blog. All opinions are 100% my own.
Choosing a Stencil Over WallpaperWhen we first laid eyes on our current rental's living room, I instantly knew the fireplace wall would become some sort of feature wall. Not only is it the focal point of the entire room, but about 12' of the wall protrude forward about 8', creating a pronounced bump-out that was literally begging for some sort of fun treatment.
In all honestly, my original plan was to cover the bump out in peel and stick wallpaper. It is my go-to product for accent walls, after all; and I could easily find several patterns that would make sense in this space.
But at 8' high and 12' feet wide, this single section of wall would have likely cost me ~$200. And having already tackled some really large wallpaper projects in this house, I was simply looking for a cheaper option that would provide the same design impact as wallpaper.
I've never stenciled a wall before, so I figured this was the perfect 'small' project to learn! And sure enough'after (admittedly) quite a bit of effort'I was indeed able to achieve a phenomenal stenciled focal wall'but on the cheap!
Supplies NeededHere is what you need to stencil a wall:
Both acrylic craft paint (yep, the kind you buy at the craft store in small bottles) or latex paint (like in cans from the hardware store) can successfully be used for wall stenciling.
Cutting Edge Stencils recommends that you use 'flat' paint (base coat and stencil coat) for optimum adhesion, smooth finish, and minimal seepage. I used an Eggshell finish (for both colors) with little issue. That said, oil-based paints and spray paints are not recommended for interior wall stenciling projects.
The amount of paint required will very much depend on the size of your wall, as well as the particular stencil pattern you choose.
For the base coat, you will need however much paint is required to give your wall (at least) a single, good coat. For my 8' x 12' wall, I used not even a half gallon of Behr Marquee paint in Edgecomb Grey.
As you will learn further down in this post, the best way to avoid paint seepage is to use as little paint as possible. As such, you will likely not use much paint at all. In fact, I used the final remnants of a can of white paint I already had on hand.
If you're buying new paint for this project, I would consider getting one or two sample sizes (8 oz) or a few acrylic bottles to start. You can always get more as needed.
Video TutorialIf you'd like to watch how to stencil a wall, here is a 3-minute video of the entire process! Full picture/text instructions are below the video. (Video not loading for you? You can watch it HERE!)
How to Stencil a Wall | Step-By-Step
Let me first break down this project for you from start-to-finish. Then at the bottom of this post, I'll share aaaaaaall the stenciling tips and tricks I learned along the way!
Start by picking out your wall stencil design and which colors you will do it in.
One of the best parts of using a stencil instead of wallpaper is that you have so much more control over both the pattern and the colors. Countless stencil patterns now exist, ranging from florals and mandalas to geometrics and tiles. And since you can get paint in practically any color, you can really bring any vision to life.
With different floral wallpapers in the two adjoining rooms (the dining room and foyer), I wanted something understated, monochromatic, and geometric for this wall. This herringbone tile pattern caught my eye immediately for its simplicity; and I knew adding the white design over the beige wall color (also throughout the rest of the room) would provide just enough interest on this bump-out without competing with other patterns around the room.
With your stencil and paints in hand, the next step is to apply the base coat of paint to your wall(s). You will have to consider your particular stencil in order to figure out which color this should be. For this herringbone pattern, I wanted the 'grout' lines to be white, so I needed to the wall color to be beige first.
NOTE: Whether you need one or two coats of your base color is up to you. If your stencil pattern will cover most of your base color, you can likely get away with a single coat. But if your stencil pattern shows most of the base color (like mine does), you may need two good coats of the base color before moving on.
With your base coat applied and fully dry, it's time to start stenciling your wall! And to do that, you're going to need to determine your initial placement.
Every wall and every pattern will call for something different. You may want to mark the center of your wall with a pencil (so that the entire pattern is centered), or you can choose to start in a corner (like I did).
Your initial stencil placement is the most important, as it will dictate how the rest of the pattern lays out. As such, take care to get it perfectly level. This clip-on level makes it so easy to place the stencil, but you can also hold up a small level against the plastic edge if needed.
Before putting up your stencil for the first time, I also recommend placing strips of painter's tape around the entire perimeter of the stencil.
Then with the level and tape pre-attached, you can stick it right to the wall once you determine the right spot.
With the stencil in place, use either a stencil brush or 4' roller to apply the thinnest application of paint possible.
One of the most important things to learn with stenciling (and you'll learn it fast if you forget) is to use as little paint as possible every time you apply it to the stencil. The #1 reason you will end up with seepage under the stencil is because you use too much paint.
So whether you use a brush or roller, after you load it with paint, always then 'offload' it by rolling/pouncing your tool to rid it of as much excess paint as possible.
To apply thin coats of paint, roll right over the stencil (with medium pressure) or use a 'pouncing' motion with a stencil brush. Always avoid 'brushing,' as that can also encourage paint under the edges of the stencil and muddy your design.
After you apply paint to all the 'open' areas of your stencil, peel it up off the wall.
No, the paint doesn't need to be dry; and yes, this can be a little scary. But go ahead'peel off the stencil to reveal your freshly-painted design underneath!
If you want to learn more, please visit our website wall stencil for painting.
Every stencil will be made a little differently, but there will always be 'registration marks' to help you line up the stencil for your next application. Yes, this typically means that you have to lay the stencil down over wet paint you just applied, but it's okay! Line up the stencil with your previous application, double-check the levelness, and re-secure the stencil to the wall (using the same strips of tape).
Once in place, apply more paint as described above.
Continue working down the wall, matching up the stencil with the previously painted registration marks to create a continuous pattern. As you approach the floor/baseboards, stop. You'll clean up the edges later on in the project.
Once you've completed a single vertical application all the way down the wall, move horizontally to start the next stretch. Just like before, line up the stencil with the previously painted design, secure it to the wall, and roll on more paint.
Continue working down in columns and then across the entire wall until most of the wall is covered in pattern.
Once the full wall is covered in pattern, you will now need to go back and re-visit all the edges (i.e., corners, ceiling, molding, and floor). Notice below that my initial application didn't stretch all the way to ceiling, the baseboards, or along the mantel. To reach into these areas, you have a few options.
Cutting Edge Stencils provides a 'ceiling' or 'edge' stencil: a smaller, cut-down version that allows you to get into smaller areas. Use this smaller stencil exactly as you did the larger version in order to fill in these outer gaps.
However, depending on the pattern, even this smaller stencil may not get all the way to the edges. As your pattern requires, you may need to bend the larger stencil into corners/edges in order to create the continuous pattern.
TIP! Bending the rigid stencil can become quite difficult. I found switching to spray adhesive (to hold the stencil in place) and a stencil brush (to get into the smaller areas) better for the edges.
A word of warning here: stenciling the entire wall is a fairly speedy process; but filling in all the edges can take a lot of time since you have to match the pattern and work the stencil into tight spots'over and over and over. I recommend working in batches and taking breaks as you get tired/frustrated.
Before putting your stencils and paint away for good, you may need to stencil over any special features that are on your wall. For this particular wall, I also needed to stencil down the side of the bump out'
'as well as over our cord concealers.
Curious how we concealed the TV cords on this wall? See here: How to Hide TV Wires Above a Fireplace (When You Can't Go Through the Wall)
In these instances, I found it helpful to cut the stencil down into even smaller sections so I could work on these tight areas. However, use caution when cutting apart your stencil, as you can disrupt the pattern or ruin its usability entirely. Only cut the stencil apart, as needed, at the very end of your project.
If you like pristine, clean paint projects'then stenciling a wall is likely not for you. Despite being as careful as possible and loading up my roller/brush with as little paint as possible, I still ended up with a fair amount of bleeding, spots, and mis-aligned pattern.
Thankfully, though, fixing this is as simple as using some leftover base coat paint!
Almost like using an eraser, simply dab some base coat paint over the messes to clean up mistakes and 'sharpen the focus' on the entire pattern.
Tips & Tricks for Stenciling WallsWhen faced with such a big wall, I was really thankful to have the foam roller. The paint really went on quickly, whereas using a stencil brush would have significantly increased how long each application took.
That said, when I got to the ceiling, baseboards, and mantel trim, the roller was too unwieldy. I really needed the precision and control of the stencil brush to adequately get into the tighter spots.
So my best advice is to have both application methods on hand, and feel free to move back-and-forth between the two as needed.
I was able to secure the stencil to my wall using painter's tape for all the flat wall, full-stencil applications. It wasn't until I got into the bends of the ceilings and edges of the mantel that tape just wasn't holding the stencil flush-enough against the wall. For these areas, I switched the spray adhesive on the back of the stencil, which yielded much better results.
However, while the spray adhesive definitely held the stencil nice-and-tight to the wall, there are a few things to know about using spray adhesive on this project:
So while I was happy to have spray adhesive on hand for the end of this project, I wouldn't personally use it as the primary method for holding the stencil on the wall.
I've already mentioned this a few times, but it's SO worth reiterating. When stenciling, load up the roller/brush with as little paint as possible. Excess paint is the primary reason you'll experience bleeding under the stencil, so just get in the habit of clearing your roller/brush of paint every single time. In this project, a little goes a really long way.
Even with using as little paint as possible, I was really surprised how 'gunked up' the stencil became after about 10-15 applications. All the excess paint that stuck to the front of the stencil not only gathered along the open edges (allowing less paint to come through and create the pattern on the wall) but also caused the stencil to become quite heavy (and therefor, it pulled away from the wall during application).
If you find that the stencil is just becoming too wet/heavy with paint and is preventing you from getting a crisp application, it's time to clean it (usually soap and water is sufficient). Although it can be a bit of a nuisance to have to stop and clean the stencil, you'll get more frustrated at the imperfect results you're getting from the heavy stencil.
NOTE: By the end of this single wall, my stencil had really started to lose it's rigidity. Had I been doing a larger wall or full room, I would have liked to have a second/fresh stencil. If you plan on tackling a lot of wall space, consider buying more than one stencil.
I do not 'demand' or even expect perfection in my DIY projects. My curtain hems aren't always straight, my pillow covers don't always fit right, and my wallpaper panels don't always line up. But I was surprised how much the 'imperfectness' of this project bothered me.
While the initial applications were fairly easy and clean; as the project wore on, I started to have quite a bit of smudging, bleeding, misalignment, etc. This was mostly due to 1) my stencil getting too heavy with paint, and 2) me getting tired. And I definitely had moments when I felt like I was just making a big ol' mess of our wall.
But then I'd take a step back and realize that all those little imperfections didn't really detract from the overall impact of the wall. Sure, there are some bleeds, messed-up patterns, and inconsistent coverage'but as a whole, the wall looks complete and honestly: quite spectacular!
So if you find yourself stressing over the 'messiness' of this project: take a deep breath and take a step back. I bet your wall looks amazing! (Plus, touch up paint really does make everything better!)
Stencil or Wallpaper? Time Versus MoneyWhen I first embarked on this wall stencil project, I was focused on one thing: saving money. I wanted the wallpaper look without the wallpaper cost. And that is most certainly what I got. Since I used 100% leftover paint, this wall required just the cost of the stencil and supplies (about $50). But what I didn't appreciate at the start'was that this cost-savings would come at the expense of my time.
Without a doubt, stenciling this wall took MUCH longer than hanging wallpaper panels would have. There was also added mess and clean-up that you mostly skip when applying wallpaper (at least the peel-and-stick kind). I had to re-visit this wall on four different occasions to complete it, mostly because of the mess of the paint and the complexity of the edges. I could only do so much until I just needed a break.
So while I do love that I was able to indeed get a 'look for less,' I think it's important to remember that when applying an amazing all-over pattern to a (large) wall, you have to decide what you want to spend: time or money.
Gold Sconces
In the end, this wall has seen quite the gratifying transformation, including a re-painted fireplace surround, a complicated cord concealing project, and new renter-friendly lighting, I'm so glad I gave this stencil project a try, as it's another great 'tool' in my renter-friendly toolbox. Yes, stenciling takes some work; but it also allows you to transform your walls in a pretty inexpensive and un-doable way!
See You Soon!
Megan
For more information, please visit types of paint brushes for walls.
Previous: 5 Things to Know Before Buying wrench manufacturer
Next: Decorative Finishes: The Use of Stencils in Historic Interiors
If you are interested in sending in a Guest Blogger Submission,welcome to write for us!
All Comments ( 0 )